Insurance Requirements
New standard for the insurance the Contractor and its lower tiers carry: the coverages, with every limit left for the Owner to set, the conditional coverages a project adds, additional insureds and waiver of subrogation, builder's risk, certificates and proof of coverage, and how long coverage must run.
Showing changes from Initial revision
to Rev 1
in Insurance Requirements.
+---
+title: Insurance Requirements
+category: General Requirements
+description: >
+ When to use: the administrative framework for the insurance the Contractor and its lower tiers carry on any construction contract, read together with the Agreement, the General Conditions, and the Supplementary Conditions. States once the coverages the Contractor carries and the limits the Owner sets for each as undefaulted fields, the conditional coverages a particular project adds (pollution, delegated-design professional liability, watercraft, aircraft and unmanned aircraft, railroad protective), the additional insureds and the endorsements that protect them during and after the Work, the waiver of subrogation, who purchases the builder's risk insurance on the Work and on what form, at what value, with what deductible and which extensions, the certificates and endorsements delivered before mobilization and kept current after it, the insurer qualification, the notice of cancellation, the disclosure and approval of deductibles and self-insured retentions, the flow-down to subcontractors and the collection of their certificates, and how long each coverage stays in force after completion, so that an Owner's representative can read every field and know what is being decided and the Supplementary Conditions carry only what this standard leaves to them.
+ Not intended for: surety bonds, the correction period, and warranties ([[sync/warranties-and-bonds]]); the indemnification the Contractor owes the Owner and the Engineer, which the General Conditions state and this standard only insures; the certificate of insurance furnished with a bid or before award as a procurement step ([[sync/bidding-procedures]]); the Owner's own property insurance on the existing facility beyond the interface with the Work; the Engineer's professional liability, which the Agreement between the Owner and the Engineer governs; the Contractor's safety program and the loss control the insurer requires of it; and the insurance a product standard requires of a particular service provider, which that standard states for itself.
+---
+
+# Scope {toc}
+
+## This standard establishes the administrative requirements for the insurance the Contractor and every lower tier carry on the Work: the coverages, the limits the Owner sets for each, the parties protected and the endorsements that protect them, the property insurance on the Work itself, the proof of coverage delivered before mobilization and kept current after it, and the time each coverage stays in force after completion, on any project and under any Division of the Specifications. {note}
+
+## The insurance obligations on a construction contract originate in the Agreement, the General Conditions, and the Supplementary Conditions, which are contract instruments between the Owner and the Contractor. A subcontractor or a supplier usually receives only the technical sections for its trade and never reads them, and the limits the Owner's counsel wrote into the Supplementary Conditions reach the second tier, if at all, as a line in a subcontract form. This standard carries the obligations into the project manual, where every reader of a technical section finds them, and it states the administrative detail those instruments leave open: what a certificate has to show, when it is delivered, who collects the subcontractors' certificates, and what the Owner does when coverage lapses. {note}
+
+## The limits are the Owner's decision and not the Engineer's. The Owner's risk manager or insurance advisor and the Owner's counsel set them against the exposure the project creates, the Owner's own insurance program, and the claims the Owner has seen, and the same coverage is carried at very different limits by a small district and a regional utility. For that reason every limit field in this standard is left without a default, and the setpoints offered are the amounts in common use rather than a recommendation. An Owner's representative reading the datasheet is reading a list of decisions the Owner makes, not a list the Engineer has already made for it. {note}
+
+## The Contractor shall comply with this standard in addition to any insurance requirement stated in the Agreement, the General Conditions, the Supplementary Conditions, or a technical standard.
+
+## Where a requirement of this standard conflicts with the Agreement, the General Conditions, or the Supplementary Conditions, those documents shall govern.
+
+## The following are outside the scope of this standard: {note}
+
+- Surety bonds, the correction period, the general warranty, and the special warranties, which [[sync/warranties-and-bonds]] governs
+- The indemnification the Contractor owes the Owner, the Engineer, and their consultants, which the General Conditions state and which the contractual liability coverage required here insures but does not define
+- The certificate of insurance furnished with a bid or before award as a step in the procurement, which [[sync/bidding-procedures]] lists and which is satisfied by the certificates this standard describes
+- The Owner's own property insurance on the existing facility, except where this standard requires the builder's risk policy to extend to the interface between the existing facility and the Work
+- The Engineer's professional liability insurance, which the Agreement between the Owner and the Engineer governs
+- The Contractor's safety program, the site safety plan, and the loss control measures the Contractor's insurer requires, which are the Contractor's means and methods
+- The product or professional liability insurance a technical standard requires of a particular service provider, such as a water treatment chemistry supplier or a pesticide applicator, which that standard states and this standard does not duplicate
+
+# Insurance Terms {toc}
+
+## The following terms are used in this standard with the meanings given here: {note}
+
+- The each occurrence limit is the most the insurer pays for all claims arising from one accident or event, and the aggregate limit is the most the insurer pays for all claims during the policy period, regardless of how many occurrences there are
+- The products and completed operations aggregate is the separate aggregate limit that applies to claims arising from the Work after it is put to its intended use or after the Contractor has left the site, as distinct from claims arising while the Work is in progress
+- Completed operations coverage is the part of the general liability policy that answers claims for bodily injury or property damage arising from the completed Work, and it is the coverage a claim in year three of a ten-year repose period is made under
+- An additional insured is a party, other than the named insured that bought the policy, to whom the insurer extends coverage by endorsement for liability arising out of the named insured's work, and an additional insured has rights under the policy only to the extent the endorsement grants them
+- Primary and non-contributory means that the Contractor's policy responds to a covered claim first and in full, before any policy the additional insured carries for itself is called on, and without asking that policy to share the loss
+- A waiver of subrogation is the insurer's agreement, by endorsement, not to pursue the party named in the waiver to recover what the insurer paid its own insured
+- An occurrence policy covers an injury or damage that happens during the policy period regardless of when the claim is made, and a claims-made policy covers a claim first made during the policy period, with a retroactive date before which the underlying event is not covered and an extended reporting period that keeps the policy open to claims after it ends
+- Builder's risk insurance is property insurance on the Work itself while it is under construction, covering physical loss to the Work, the materials, and the temporary works from the perils the policy names, as distinct from liability insurance, which covers injury or damage to others
+- A deductible is the part of a covered loss the insured bears before the insurer pays, and a self-insured retention is a stated amount of each loss the insured pays and defends itself before the policy attaches at all
+- An umbrella or excess liability policy sits above the general liability, automobile liability, and employer's liability policies and pays once their limits are exhausted, and it follows form when it adopts the terms of the underlying policies rather than its own narrower ones
+- A certificate of insurance is a summary, issued by the insurer or its agent, of the policies in force on the date it was issued, and it confers no coverage on anyone; the endorsements attached to it are what change the policy
+- A lower tier is a subcontractor, a sub-subcontractor, a supplier that performs work on the site, a hauler, or a consultant engaged, at any level, under the Contractor
+
+# Referenced Standards {toc}
+
+## The insurance and its administration shall comply with the latest adopted edition of each of the following unless a specific edition is cited or the Contract Documents direct otherwise.
+
+## Where referenced documents conflict, the more stringent requirement shall govern unless the Engineer of Record directs otherwise in writing.
+
+| Standard | Title |
+|----------|-------|
+| AIA A201 | General Conditions of the Contract for Construction (insurance and bonds) |
+| EJCDC C-700 | Standard General Conditions of the Construction Contract (bonds and insurance) |
+| ConsensusDocs 200 | Standard Agreement and General Conditions Between Owner and Constructor (indemnity, insurance, waivers, and bonds) |
+| ACORD 25 | Certificate of Liability Insurance |
+| ACORD 28 | Evidence of Commercial Property Insurance |
+
+## The general conditions in common use each carry an insurance article that names the coverages, assigns the builder's risk to one party, and leaves the limits to the Supplementary Conditions or to an insurance exhibit the Owner's counsel completes, and the three publishers differ in how they word the additional insured and waiver provisions and in which party buys the property insurance by default. The workers' compensation statute of every state sets the coverage an employer in that state carries, and no contract term changes it. The certificate forms in the table are the forms insurers' agents issue by default, and an Owner that requires its own form says so in the Supplementary Conditions. {note}
+
+# Submittals {toc}
+
+## Insurance Submittals Before Mobilization {toc}
+
+### The Contractor shall submit the following before mobilizing to the site, and the Owner may withhold the notice to proceed and the first payment until they have been received and accepted:
+
+- A certificate of insurance for each coverage this standard requires, showing the insurer, the policy number, the policy period, the limits, and the certificate holder
+- The additional insured endorsement to each liability policy, covering ongoing and completed operations and naming the parties this standard requires
+- The primary and non-contributory endorsement, or the policy provision that has that effect, for each liability policy
+- The waiver of subrogation endorsement to each policy on which this standard requires one
+- The builder's risk policy or its certificate, where the Contractor purchases it, showing the form, the insured value, the deductible, and the extensions carried
+- A statement of every deductible and self-insured retention on every required policy
+- Evidence of each insurer's authorization in the state of the project and of its financial strength rating
+
+```datasheet
+label: Insurance Submittals Required Before Mobilization
+type: checkbox
+options:
+ - Certificate of insurance for each required coverage
+ - Additional insured endorsements, ongoing and completed operations
+ - Primary and non-contributory endorsements
+ - Waiver of subrogation endorsements
+ - Builder's risk policy or certificate, where Contractor-purchased
+ - Statement of deductibles and self-insured retentions
+ - Insurer authorization and rating evidence
+default:
+ - Certificate of insurance for each required coverage
+ - Additional insured endorsements, ongoing and completed operations
+ - Primary and non-contributory endorsements
+ - Waiver of subrogation endorsements
+ - Statement of deductibles and self-insured retentions
+ - Insurer authorization and rating evidence
+constraint: all_of
+```
+
+### Insurance submittals shall be transmitted and tracked through the submittal procedure of [[sync/submittal-and-quality-procedures]].
+
+### Where the Instructions to Bidders required a certificate of insurance before award under [[sync/bidding-procedures]], that certificate shall not substitute for the submittals of this article unless it already shows every coverage, limit, and endorsement this standard requires.
+
+### A certificate that arrives without its endorsements is the recurring defect, and it is discovered when a claim is made and the additional insured finds it has a summary and no coverage. Reviewing the endorsements before mobilization, when the Contractor still needs the notice to proceed, is the point at which the correction costs nothing. {note}
+
+## Insurance Submittals During and After the Work {toc}
+
+### The Contractor shall submit the following at the time stated for each:
+
+- A renewal certificate and its endorsements for each policy that expires before final completion, before the expiration date
+- A replacement certificate within fourteen days after any policy is cancelled, non-renewed, or materially changed
+- The certificates and endorsements of each lower tier, within seven days after the Owner's written request
+- A certificate showing that completed operations coverage remains in force, on each anniversary of final completion for the duration this standard requires
+- Certified copies of any policy and its endorsements, within fourteen days after the Owner's written request
+
+```datasheet
+label: Insurance Submittals Required During and After the Work
+type: checkbox
+options:
+ - Renewal certificates before expiration
+ - Replacement certificates after cancellation or change
+ - Lower tier certificates on request
+ - Annual completed operations certificates
+ - Certified policy copies on request
+default:
+ - Renewal certificates before expiration
+ - Replacement certificates after cancellation or change
+ - Lower tier certificates on request
+ - Annual completed operations certificates
+ - Certified policy copies on request
+constraint: all_of
+```
+
+### Policies renew on the insurer's calendar and not the project's, and a two-year project crosses at least one renewal on every policy. The renewal certificate is what tells the Owner the coverage carried on, and the annual completed operations certificate is what tells the Owner, years later, that the coverage a claim would be made under still exists. {note}
+
+# Coverages and Limits {toc}
+
+## Commercial General Liability {toc}
+
+### The Contractor shall carry commercial general liability insurance written on an occurrence basis, covering premises and operations, products and completed operations, contractual liability for the indemnification the General Conditions require, personal and advertising injury, and bodily injury and property damage arising from explosion, collapse, and underground hazards.
+
+### The each occurrence limit of the commercial general liability insurance shall be as indicated in the datasheet.
+
+```datasheet
+label: General Liability Each Occurrence Limit
+type: range
+unit: '$ million'
+options:
+ min: 0.5
+ max: 10
+ setpoints: [0.5, 1, 2, 5, 10]
+constraint: min
+```
+
+### The general aggregate limit of the commercial general liability insurance shall be as indicated in the datasheet, and shall apply separately to this project.
+
+```datasheet
+label: General Liability General Aggregate Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 20
+ setpoints: [1, 2, 4, 5, 10, 20]
+constraint: min
+```
+
+### The products and completed operations aggregate limit of the commercial general liability insurance shall be as indicated in the datasheet.
+
+```datasheet
+label: Products and Completed Operations Aggregate Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 20
+ setpoints: [1, 2, 4, 5, 10, 20]
+constraint: min
+```
+
+### The each occurrence limit is sized to the worst single event the Work can produce, a trench collapse or a chlorine release, and the aggregate to the number of such events a policy year can hold. A general aggregate that is not endorsed to apply per project is shared with every other job the Contractor has running, and a large loss on another site exhausts the limit this project was counting on; the per-project endorsement is what keeps the stated aggregate whole for this Work. The explosion, collapse, and underground hazard coverage is named because older policies excluded it and because excavation beside a live main and blasting near a structure are exactly the operations it answers. An occurrence form is required because a claim for a defect in the completed Work is often made years after the policy that was in force when the Work was done has expired, and an occurrence policy still answers it. {note}
+
+## Automobile Liability {toc}
+
+### The Contractor shall carry automobile liability insurance covering every owned, hired, and non-owned vehicle used in connection with the Work, with a combined single limit for bodily injury and property damage as indicated in the datasheet.
+
+```datasheet
+label: Automobile Liability Combined Single Limit
+type: range
+unit: '$ million'
+options:
+ min: 0.5
+ max: 5
+ setpoints: [0.5, 1, 2, 5]
+constraint: min
+```
+
+### Where the Work includes hauling a regulated waste, a contaminated soil, a sludge, or a chemical, the automobile liability insurance shall cover pollution arising from the loading, transport, and unloading of that material, by endorsement or by a separate transportation pollution policy.
+
+### The hired and non-owned coverage is what answers the accident in a rented pickup or an employee's own truck sent for parts, which an owned-auto policy alone does not. The pollution clause is named because a general liability policy excludes pollution from a vehicle and a standard automobile policy excludes pollution of the cargo, so a sludge tanker that overturns on the road falls between the two unless one of them is endorsed. {note}
+
+## Workers' Compensation and Employer's Liability {toc}
+
+### The Contractor shall carry workers' compensation insurance as the statute of the state of the project requires, and as the statute of every other state in which an employee working on the project was hired requires.
+
+### The Contractor shall carry employer's liability insurance with a limit, for each accident, for disease for each employee, and for disease in the aggregate, as indicated in the datasheet.
+
+```datasheet
+label: Employer's Liability Limit
+type: range
+unit: '$ million'
+options:
+ min: 0.5
+ max: 5
+ setpoints: [0.5, 1, 2, 5]
+constraint: min
+```
+
+### Where the Work is performed on, over, or adjacent to navigable water, including an intake, an outfall, a dock, or a barge-mounted operation, the workers' compensation insurance shall include longshore and harbor workers' compensation coverage and, where a crew is assigned to a vessel, maritime employer's liability coverage.
+
+### Workers' compensation is statutory, and the statute sets what it pays, so the standard sets no limit for it. Employer's liability is the companion coverage for the injured employee's claim that falls outside the statute, and for the third-party suit in which a general contractor sued by a subcontractor's employee brings the employer in; the three stated amounts are the form in which that policy's limit is written, and the field states one amount for all three. An employee injured over navigable water is compensated under a federal scheme the state policy does not respond to, which is why that coverage is named by condition rather than left to the Contractor to discover after the injury. {note}
+
+## Umbrella or Excess Liability {toc}
+
+### The Contractor shall carry umbrella or excess liability insurance, following the form of the underlying commercial general liability, automobile liability, and employer's liability policies, with a limit for each occurrence and in the aggregate as indicated in the datasheet.
+
+```datasheet
+label: Umbrella or Excess Liability Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 100
+ setpoints: [1, 2, 5, 10, 25, 50, 100]
+constraint: min
+```
+
+### The limits required by this standard for commercial general liability, automobile liability, and employer's liability may be met by a combination of the primary policy and the umbrella or excess policy, provided the umbrella or excess policy follows form and extends to the additional insureds on the same terms as the primary policy.
+
+### The umbrella is where the limit the Owner is relying on usually lives, because a primary general liability policy is written at the amounts the Contractor's agent writes for every client and the umbrella is sized to the job. A policy that does not follow form carries its own exclusions, and a loss the primary covers can be refused above the primary limit by an excess policy that excludes it, which is why following form is a requirement and not a preference. Allowing the combination is what lets a Contractor with a one million dollar primary meet a two million dollar requirement without re-papering its program, and it costs the Owner nothing as long as the umbrella picks up where the primary stops. {note}
+
+## Conditional Coverages Selected by the Work {toc}
+
+### The Contractor shall carry, in addition to the coverages above, each conditional coverage indicated in the datasheet, at the limit indicated for it.
+
+```datasheet
+label: Conditional Coverages Required
+type: checkbox
+options:
+ - Contractor's pollution liability
+ - Professional liability for delegated design
+ - Watercraft liability
+ - Aircraft liability
+ - Unmanned aircraft liability
+ - Railroad protective liability
+constraint: all_of
+```
+
+### Where contractor's pollution liability is indicated, it shall cover bodily injury, property damage, and cleanup cost arising from a pollution condition caused by the Work, on the site and from the transport and disposal of material removed from it, with a limit for each condition as indicated in the datasheet.
+
+```datasheet
+label: Contractor's Pollution Liability Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 25
+ setpoints: [1, 2, 5, 10, 25]
+constraint: min
+```
+
+### Where professional liability for delegated design is indicated, the Contractor, or the licensed engineer performing the delegated design under the Contractor, shall carry professional liability insurance covering the design services performed under the Contract, with a limit for each claim as indicated in the datasheet.
+
+```datasheet
+label: Delegated Design Professional Liability Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 10
+ setpoints: [1, 2, 5, 10]
+constraint: min
+```
+
+### Where watercraft liability is indicated, it shall cover every owned, hired, and chartered vessel used in the Work, with a limit as indicated in the datasheet.
+
+```datasheet
+label: Watercraft Liability Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 25
+ setpoints: [1, 5, 10, 25]
+constraint: min
+```
+
+### Where aircraft liability is indicated, it shall cover every manned aircraft owned, hired, or chartered for the Work, including a helicopter lift, with a limit as indicated in the datasheet.
+
+```datasheet
+label: Aircraft Liability Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 50
+ setpoints: [1, 5, 10, 25, 50]
+constraint: min
+```
+
+### Where unmanned aircraft liability is indicated, it shall cover every unmanned aircraft operated over or near the site for the Work, including the progress photography under [[sync/construction-progress-documentation]], with a limit as indicated in the datasheet.
+
+```datasheet
+label: Unmanned Aircraft Liability Limit
+type: range
+unit: '$ million'
+options:
+ min: 0.5
+ max: 10
+ setpoints: [0.5, 1, 2, 5, 10]
+constraint: min
+```
+
+### Where railroad protective liability is indicated, the Contractor shall furnish a railroad protective liability policy in the name of the railroad, on the form and with the aggregate the railroad requires, with an each occurrence limit as indicated in the datasheet or the limit the railroad requires, whichever is greater.
+
+```datasheet
+label: Railroad Protective Liability Each Occurrence Limit
+type: range
+unit: '$ million'
+options:
+ min: 1
+ max: 25
+ setpoints: [1, 2, 5, 10, 25]
+constraint: min
+```
+
+### Each conditional coverage answers an exposure a general liability policy excludes, and each is selected by a fact about the Work rather than by preference. Pollution liability is selected by sludge, process chemicals, contaminated soil, a bypass that could spill under [[sync/temporary-bypass-pumping]], or a sewer that could surcharge, since the general liability policy excludes pollution and the plant is full of it. Professional liability is selected by delegated design: a sealed bypass plan, a temporary shoring or cofferdam design, a precast or steel connection design, or any other submittal that [[sync/submittal-and-quality-procedures]] requires a licensed engineer to seal, because the general liability policy excludes professional services and the engineer who sealed the shoring is the party a collapse claim names. Watercraft is selected by a barge, a workboat, or a diver's tender at an intake or an outfall. Aircraft is selected by a helicopter lift of a rooftop unit or a transmission structure, and unmanned aircraft by the drone that flies the progress photography, which a general liability policy also excludes as an aircraft. Railroad protective liability is selected by work within the right-of-way of a railroad, which will not issue the entry permit without a policy in its own name on its own form. {note}
+
+### Contractor's pollution liability and professional liability may be written on a claims-made basis, in which case the retroactive date shall be not later than the date the first Work under the Contract was performed, and the coverage shall be maintained, or an extended reporting period purchased, for the completed operations duration this standard requires.
+
+### Pollution and professional policies are commonly sold only as claims-made, and a claims-made policy covers nothing that happened before its retroactive date and nothing reported after it ends. A retroactive date set after the Work started leaves the early Work uninsured, and a policy allowed to lapse after completion leaves the claim that arrives in year three with no policy to be made against, which is what the retroactive date and the extended reporting period requirements prevent. {note}
+
+# Additional Insureds and Policy Terms {toc}
+
+## Additional Insured Parties {toc}
+
+### The Contractor shall name the Owner, the Engineer, the Engineer's consultants, and each party indicated in the datasheet as additional insureds on the commercial general liability, automobile liability, umbrella or excess liability, and, where carried, contractor's pollution liability policies, by an endorsement covering both ongoing operations and completed operations.
+
+```datasheet
+label: Other Additional Insureds Named by the Owner
+type: text
+```
+
+### The additional insured endorsement shall cover liability arising out of the Contractor's work, including liability arising from the additional insured's own acts or omissions in connection with the Work to the extent the law of the jurisdiction of the project permits.
+
+### An additional insured endorsement that covers ongoing operations alone ends when the Contractor leaves the site, and the claim for the completed Work, made against the Owner years later, finds the Owner with no coverage under the Contractor's policy; the completed operations endorsement is the separate endorsement that carries the Owner's status forward. The Engineer and its consultants are named because a suit arising from a construction accident names the Owner and the Engineer together, and the Engineer's own professional liability policy does not respond to a claim for a site accident. The parties the Owner adds in the datasheet are the ones the project's facts supply: a lender, a lessor, a utility that owns the easement, a construction manager, a municipality that issued the right-of-way permit. The clause on the additional insured's own acts is written to the extent the law permits because some states void an insurance requirement that covers a party's sole fault. {note}
+
+## Primary and Non-Contributory Coverage {toc}
+
+### Each policy on which the Owner, the Engineer, and the other additional insureds are named shall be primary to, and shall not seek contribution from, any insurance or self-insurance the additional insureds carry for themselves.
+
+### Without this term, the Contractor's insurer and the Owner's insurer each point at the other when a claim arrives, and the Owner's own policy, which was bought for the Owner's own operations, pays part of a loss the Contractor's work caused and carries the claim on the Owner's loss history. The term settles the order before the claim exists. {note}
+
+## Waiver of Subrogation {toc}
+
+### The Contractor shall waive, and shall cause its insurers to waive by endorsement, every right of recovery against the Owner, the Engineer, the Engineer's consultants, and the other additional insureds, on the commercial general liability, automobile liability, workers' compensation and employer's liability, umbrella or excess liability, and, where carried, contractor's pollution liability policies, to the extent a loss is covered by those policies.
+
+### The waiver of subrogation shall extend to the builder's risk policy, whichever party purchases it, in favor of the Owner, the Contractor, the Engineer, the Engineer's consultants, and every lower tier whose property is insured under it, for loss to the Work the policy covers.
+
+### A workers' compensation insurer that pays an injured employee acquires that employee's claim against whoever caused the injury, and on a construction site that is frequently the Owner, whose operator opened a valve, or the Engineer, whose inspector was present. The waiver stops the insurer from pursuing the parties the contract was written to protect, and it costs the Contractor a small premium charge. On the builder's risk policy the waiver is what makes the insurance the single answer to a loss to the Work, instead of the first move in a suit between the parties over who caused the fire. {note}
+
+## Completed Operations Duration {toc}
+
+### The Contractor shall maintain the commercial general liability insurance with the products and completed operations coverage, and the umbrella or excess insurance above it, with the Owner and the other additional insureds named for completed operations, for the period indicated in the datasheet after final completion.
+
+```datasheet
+label: Completed Operations Coverage Duration After Final Completion
+type: range
+unit: years
+options:
+ min: 1
+ max: 10
+ setpoints: [1, 2, 3, 5, 10]
+constraint: min
+```
+
+### The duration is set against the statute of repose for construction claims in the jurisdiction of the project, which is the last date a claim for a defect in the completed Work can be brought and which runs from four to twelve years depending on the state. A duration that ends before the repose period leaves the Owner, as an additional insured, without coverage for a claim it can still face, and a duration that runs to the full repose period is paid for in every renewal premium the Contractor carries for that long, which is why the period is the Owner's decision and is left to it. {note}
+
+## Notice of Cancellation {toc}
+
+### Each policy required by this standard shall be endorsed to provide the Owner written notice, not less than the number of days indicated in the datasheet before the effective date, of cancellation, non-renewal, or a reduction in coverage or limits below those this standard requires.
+
+```datasheet
+label: Notice of Cancellation to the Owner
+type: range
+unit: days
+options:
+ min: 10
+ max: 90
+ setpoints: [10, 30, 45, 60, 90]
+default: 30
+constraint: min
+```
+
+### Where an insurer will not endorse the policy to give notice to the Owner, the Contractor shall give the Owner the notice itself within two business days after receiving the insurer's notice, and in no case later than the number of days indicated in the datasheet before the effective date.
+
+### Thirty days is the notice the industry forms have carried for decades and is what reaches a project without discussion, and insurers customarily shorten it to ten days for cancellation for non-payment of premium. Insurers have withdrawn from promising notice to certificate holders on the certificate itself, so the notice now has to be obtained by endorsement or, failing that, placed on the Contractor, which is why the second clause exists. {note}
+
+## Insurer Qualification {toc}
+
+### Each insurer shall be authorized to transact insurance in the state of the project, or, where a required coverage is available only from a surplus lines insurer, shall be an eligible surplus lines insurer in that state placed through a licensed surplus lines broker.
+
+### Each insurer's minimum financial strength rating assigned by A.M. Best shall be as indicated in the datasheet.
+
+```datasheet
+label: Insurer Minimum A.M. Best Financial Strength Rating
+type: select
+options:
+ - No rating minimum
+ - B+
+ - A-
+ - A
+ - A+
+```
+
+### A minimum of A- is the floor most Owners who state one use, and it excludes the companies the rating agency considers vulnerable without excluding the regional carriers that write most contractors. Raising the floor to A or A+ narrows the field to the larger national carriers and raises the premium on every policy the Contractor carries. Stating no minimum leaves the qualification to state authorization alone, which a small private project accepts and a public Owner's standing program usually does not. Pollution and professional coverages are often written by surplus lines insurers, which is why the admitted-insurer requirement carries the surplus lines exception. {note}
+
+### Where an insurer's rating falls below the indicated minimum, or its authorization is revoked, during the term of a required policy, the Contractor shall replace the policy with one from a qualified insurer within thirty days after the Owner's written notice, at no cost to the Owner.
+
+## Deductibles and Self-Insured Retentions {toc}
+
+### The Contractor shall disclose, with the submittals before mobilization, every deductible and every self-insured retention on each required policy, and shall obtain the Owner's written approval of any deductible or self-insured retention that exceeds the amount indicated in the datasheet.
+
+```datasheet
+label: Deductible or Self-Insured Retention Requiring the Owner's Approval
+type: range
+unit: '$ thousand'
+options:
+ min: 0
+ max: 1000
+ setpoints: [0, 10, 25, 50, 100, 250, 500, 1000]
+constraint: exact
+```
+
+### The Contractor shall bear every deductible and self-insured retention on its own policies, and no additional insured shall be required to fund a deductible or a self-insured retention as a condition of coverage under the Contractor's policy.
+
+### A deductible comes out of the insurer's payment, so the policy still responds and the insured owes the insurer the deductible afterward; a self-insured retention has to be paid, and the claim defended, by the insured before the insurer does anything, and a large retention on a contractor that cannot fund it is the same as no coverage up to that amount. The approval threshold is set against the Contractor's size and the Owner's willingness to find out, after the loss, that the first half million is the Contractor's problem. A threshold of zero brings every deductible to the Owner for approval, which is exact and is a paperwork burden; a high threshold accepts that a large contractor's program carries large retentions by design. {note}
+
+# Builder's Risk Insurance {toc}
+
+## Purchasing Party {toc}
+
+### Builder's risk insurance on the Work shall be purchased and maintained by the party indicated in the datasheet.
+
+```datasheet
+label: Builder's Risk Purchasing Party
+type: radio
+options:
+ - The Owner
+ - The Contractor
+ - Not required, the Owner's existing property insurance covers the Work
+```
+
+### The general conditions in common use assign the builder's risk to the Owner by default, and many Owners shift it to the Contractor in the Supplementary Conditions, so the field states which was chosen rather than assuming either. An Owner-purchased policy is written on the Owner's property program, covers the interface with the Owner's existing plant without an argument about where the existing building ends and the Work begins, and leaves the Owner holding the deductible and the claim; it also leaves the Owner insuring a site it does not control. A Contractor-purchased policy sits with the party that controls the site, the hot work, the stored materials, and the subcontractors who start the fires, and it is priced into the bid, at the cost of a policy the Owner has to read to learn what its own existing structures are covered for. Covering the Work under the Owner's existing property insurance, by an installation floater or by the policy's own course of construction provision, suits a small renovation inside an operating facility, where the Work is a fraction of the insured value already on the policy, and it is confirmed with the Owner's property insurer before the Work starts rather than assumed. {note}
+
+### Where the Owner purchases the builder's risk insurance, the Contractor shall furnish the Owner, before mobilization, the completed value of the Work and the schedule of values the Owner's insurer requires, and shall report each change order that alters the completed value within fourteen days after it is executed.
+
+### Where the Owner's existing property insurance is indicated, the Owner shall confirm in writing to the Contractor, before mobilization, that the Work is covered under that insurance and the deductible that applies to it, and the Contractor shall insure its own tools, equipment, and temporary works.
+
+## Form and Insured Value {toc}
+
+### Requirements in this article apply where the Owner or the Contractor is indicated as the purchasing party.
+
+### The builder's risk insurance shall be written on an all-risk or special form, covering physical loss or damage to the Work from every peril the form does not expressly exclude, on a completed value basis equal to the full insurable value of the Work including change orders, with the Owner, the Contractor, and every lower tier named as insureds as their interests appear.
+
+### The builder's risk insurance shall cover the Work in place, the materials and equipment to be incorporated in the Work while stored on the site, and the temporary works, formwork, and scaffolding, and shall cover materials stored off the site and in transit where the extensions in this standard so indicate.
+
+### The purchasing party shall obtain the insurer's written consent before the Owner occupies or places in use any portion of the Work before substantial completion, and the Owner's partial occupancy or use under [[sync/summary-of-work-and-work-restrictions]] shall not take effect until that consent is obtained.
+
+### A builder's risk policy is written for a site under construction and most forms suspend or void coverage when the building is occupied, so the Owner that moves its operators into the new control room a month early can find the whole policy voided by the move. The consent is a routine endorsement when it is asked for and a coverage dispute when it is not. {note}
+
+## Deductible and Who Bears It {toc}
+
+### The deductible on the builder's risk insurance shall not exceed the amount indicated in the datasheet for each loss, except for the flood, earth movement, and named storm perils, for which the deductible shall be as the policy states.
+
+```datasheet
+label: Builder's Risk Deductible Each Loss
+type: range
+unit: '$ thousand'
+options:
+ min: 0
+ max: 500
+ setpoints: [0, 1, 5, 10, 25, 50, 100, 250, 500]
+constraint: max
+```
+
+### The deductible on each builder's risk loss shall be borne by the party indicated in the datasheet.
+
+```datasheet
+label: Party Bearing the Builder's Risk Deductible
+type: radio
+options:
+ - The Contractor, on every loss
+ - The Owner, on every loss
+ - The party whose act or omission caused the loss, and the Owner where no party is responsible
+```
+
+### Placing the deductible on the Contractor on every loss is the arrangement that pairs with a Contractor-purchased policy, since the Contractor chose the deductible and controls the site, and it is priced into the bid. Placing it on the Owner pairs with an Owner-purchased policy and with the Owner's wish to keep a Contractor from under-insuring to save premium, at the cost of the Owner funding the loss a subcontractor's welder caused. Placing it on the responsible party keeps the cost with the cause and reopens, on every loss, the question of who caused it, which the waiver of subrogation was meant to close. Flood, earth movement, and named storm deductibles are carved out because insurers write them as a percentage of the insured value and no stated dollar maximum survives contact with them. {note}
+
+## Extensions of Coverage {toc}
+
+### The builder's risk insurance shall include each extension of coverage indicated in the datasheet, at the sublimit the Owner accepts in writing where the policy carries one.
+
+```datasheet
+label: Builder's Risk Extensions of Coverage
+type: checkbox
+options:
+ - Flood
+ - Earth movement
+ - Named storm and windstorm
+ - Testing and startup, cold and hot
+ - Equipment breakdown during testing
+ - Materials stored off site
+ - Materials in transit
+ - Existing structures at the interface with the Work
+ - Debris removal and pollutant cleanup
+ - Delay in completion and soft costs for the Owner
+constraint: all_of
+```
+
+### A standard builder's risk form excludes or sublimits the perils a treatment plant is most exposed to, which is why they are selected here by name rather than assumed. Plants sit on rivers and in floodplains, and flood is excluded from most forms unless bought back. Earth movement is excluded where the site is not in a seismic zone and is cheap there, and expensive where it is. Testing and startup is the period when the pumps, the blowers, and the switchgear first run, and most forms stop coverage at the moment testing begins unless the extension is carried, so a motor that fails during the seven-day test is an uninsured loss without it; equipment breakdown during testing covers the internal failure of the machine itself, which the testing extension covers only when written to. Materials stored off site and in transit cover the switchgear sitting in the manufacturer's yard and the truck it rides in on, which the Owner has often already paid for under [[sync/payment-procedures]] as stored materials. The existing structures extension insures the Owner's operating plant where the Work ties into it under [[sync/maintenance-of-plant-operations]], which is the loss an Owner-purchased policy covers by default and a Contractor-purchased policy covers only when told to. Debris removal and pollutant cleanup pay to clear the site after the loss, which on a plant includes the chemical the fire released. Delay in completion pays the Owner's extra interest, rental, and operating cost while the Work is rebuilt and is bought by an Owner that has a bond issue or a consent decree running against the completion date. {note}
+
+# Lower Tiers {toc}
+
+## Subcontractor Coverages and Limits {toc}
+
+### The Contractor shall require every lower tier that performs work on the site to carry commercial general liability, automobile liability, workers' compensation and employer's liability, and, where the lower tier's work creates the exposure, each conditional coverage of this standard, at the limits indicated in the datasheet.
+
+```datasheet
+label: Lower Tier Insurance Limits
+type: radio
+options:
+ - The same limits as the Contractor
+ - The limits the Owner states in the Supplementary Conditions for lower tiers
+ - Limits the Contractor sets for each subcontract by its value and trade, not less than the statutory coverages
+```
+
+### Requiring the same limits of every lower tier is simplest to verify and is the arrangement under which the Owner's protection does not depend on which tier's employee was hurt, at the cost of a limit a small specialty subcontractor cannot buy, which the Contractor meets by not using that subcontractor or by carrying the difference. Limits the Owner states for lower tiers let the Owner set a lower floor for small trades while holding the Contractor at the full amount, which most public Owners' programs do, at the cost of a second schedule to keep current. Letting the Contractor set the limits by subcontract puts the decision with the party that carries the subcontractor risk and prices it, and leaves the Owner relying on the Contractor's own policy for whatever the subcontractor does not carry. {note}
+
+### Each lower tier's commercial general liability, automobile liability, and umbrella or excess liability policies shall name the Owner, the Engineer, the Engineer's consultants, the other additional insureds, and the Contractor as additional insureds for ongoing and completed operations, on a primary and non-contributory basis, and each lower tier's policies shall carry the waiver of subrogation this standard requires of the Contractor's.
+
+### Where a lower tier performs delegated design, hauls a regulated material, operates a vessel or an aircraft, or works within a railroad right-of-way, the conditional coverage for that exposure shall be carried by that lower tier, by the Contractor, or by both, and the Contractor shall identify which on the certificate it furnishes.
+
+### The Contractor shall include the insurance requirements of this standard that apply to a lower tier's scope in each subcontract and purchase order, and shall remain responsible to the Owner for a loss caused by a lower tier that did not carry the required insurance.
+
+### A subcontractor that never saw this standard, because its subcontract incorporated only the technical section for its trade, learns of the additional insured requirement when the claim arrives and its insurer declines to defend the Owner. Flowing the requirements into the subcontract is what makes them the subcontractor's obligation, and the Contractor's responsibility for an uninsured subcontractor is what makes the Contractor check. {note}
+
+## Collection of Lower Tier Certificates {toc}
+
+### The Contractor shall obtain the certificate of insurance and the endorsements of each lower tier before that lower tier begins work on the site, shall keep them on file for the duration of the Contract and the completed operations period, and shall furnish them to the Owner within seven days after the Owner's written request.
+
+### The Contractor shall not permit a lower tier to begin or continue work on the site while any coverage this standard requires of it has lapsed.
+
+### The Owner is not a party to the subcontract and does not collect the subcontractors' certificates itself, so the Contractor's file is the only record that a given subcontractor was insured on the day its employee fell. The right to request the file, rather than a requirement to deliver every certificate, keeps the Owner's review to the subcontracts it cares about and keeps the certificates for forty suppliers off the Engineer's desk. {note}
+
+# Certificates and Proof of Coverage {toc}
+
+## Certificate Form and Content {toc}
+
+### Each certificate of insurance shall be issued on a standard industry certificate form, such as ACORD 25 for liability and ACORD 28 for property, or on the Owner's form where the Supplementary Conditions require it, and shall be signed by an authorized representative of the insurer or its agent.
+
+### Each certificate shall identify the project by name and Contract number, shall name the Owner as certificate holder at the address stated in the Agreement, and shall show for each policy the insurer, the policy number, the policy period, each limit this standard requires, and the deductible or self-insured retention.
+
+### Each certificate shall state that the additional insured, primary and non-contributory, waiver of subrogation, and notice of cancellation requirements of this standard are met, and shall have attached the endorsement, or the policy provision, that meets each of them.
+
+### A certificate is a snapshot taken by an agent, it is issued subject to the policy, and it confers no rights on the holder; the industry forms say so on their face. The endorsements attached to it are what change the policy, and a certificate that recites the endorsements without attaching them is the defect that surfaces when the insurer, at claim time, says no such endorsement was issued. {note}
+
+### The Contractor shall furnish a copy of each certificate and its endorsements to the Engineer at the same time as to the Owner.
+
+## Right to Policies {toc}
+
+### The Owner may request a certified copy of any policy required by this standard, with every endorsement, and the Contractor shall furnish it within fourteen days after the request.
+
+### The Contractor may redact from a certified copy the premium and the rating information, and shall not redact any term, condition, exclusion, endorsement, or limit.
+
+### Most Owners never ask for the policy, and the right exists for the project on which the certificate and the endorsements do not add up, or on which the exposure is large enough that the Owner's risk manager wants to read the exclusions before the Work starts rather than after the loss. {note}
+
+## Failure to Maintain Coverage {toc}
+
+### Where any coverage this standard requires lapses, is cancelled, or is reduced below the required limits and is not replaced before the effective date, the Owner may suspend the Work until the coverage is restored, and the Contractor shall not be entitled to an extension of time or an adjustment of the Contract Sum for the suspension.
+
+### Where the Contractor does not restore a lapsed coverage within seven days after the Owner's written notice, the Owner may purchase the coverage on the Contractor's behalf and deduct the premium and the Owner's cost of placing it from sums due the Contractor, without relieving the Contractor of responsibility for any loss during the lapse.
+
+### The Owner's receipt or acceptance of a certificate, or the Owner's failure to object to one, shall not waive any requirement of this standard or relieve the Contractor of responsibility for carrying the required coverage.
+
+### The Contractor shall bear every loss, cost, and claim that the required insurance would have covered had it been in force, to the extent the loss is not covered because the Contractor did not carry, maintain, or endorse the insurance as this standard requires.
+
+### A lapse is discovered in one of two ways: at renewal, when the certificate does not arrive, or at a claim, when the coverage is found to have ended months before. The suspension right is what makes the first discovery matter, and the last clause is what makes the second discovery the Contractor's loss rather than the Owner's. {note}
+
+# Duration of Coverage {toc}
+
+## Coverage Through Final Completion {toc}
+
+### Every coverage this standard requires shall be in force before the Contractor or any lower tier mobilizes to the site and shall remain in force, without interruption, through final completion of the Work.
+
+### Workers' compensation and employer's liability, commercial general liability, and automobile liability insurance shall be in force at the required limits whenever the Contractor or a lower tier is on the site, including for corrective work under the correction period and warranty work under [[sync/warranties-and-bonds]] performed after final completion.
+
+### The builder's risk insurance shall remain in force until the date of substantial completion of the Work, or of the designated portion containing the Work, as fixed on the certificate of substantial completion under [[sync/closeout-procedures]], and that certificate shall state the date on which responsibility for insuring the Work passes to the Owner's property insurance.
+
+### Where the Owner's property insurance cannot attach on the date of substantial completion, the purchasing party shall keep the builder's risk insurance in force until it does, and the cost of the extension beyond substantial completion shall be borne by the Owner.
+
+### The gap between the day the builder's risk policy ends and the day the Owner's property policy picks up the new asset is a gap no one notices until a transformer fails in it. Fixing the transfer date on the certificate of substantial completion, which the parties sign anyway, is what closes it, and placing the cost of any extension on the Owner reflects that the delay in attaching the Owner's own policy is the Owner's. {note}
+
+## Coverage After Final Completion {toc}
+
+### The completed operations coverage and the additional insured status for completed operations shall remain in force for the duration this standard indicates after final completion, and the Contractor shall furnish the annual certificate this standard requires for each year of that period.
+
+### Where a required coverage is written on a claims-made basis, the Contractor shall keep it in force, or shall purchase an extended reporting period, through the end of the completed operations duration, and a change of insurer during that period shall carry the original retroactive date forward.
+
+### The obligations of this standard shall survive final payment and final completion for the duration of the completed operations period and for as long as any claim arising from the Work can be brought against an additional insured.
+
+# Coordination with the Agreement and Other Standards {toc}
+
+## The Contractor shall reconcile the insurance requirements of the Agreement, the General Conditions, the Supplementary Conditions, and each technical standard with this standard, and shall report in writing, before mobilization, any conflict between them.
+
+## The cost of every coverage this standard requires, including the premium for the duration after final completion, shall be included in the Contract Sum, and no adjustment shall be made for a change in the Contractor's premium during the Work.
+
+## Where the Owner requires, after the Agreement is executed, a coverage, a limit, an additional insured, or an extension this standard did not require at the time of bidding, the change shall be made by change order under [[sync/contract-modification-procedures]], and the Contractor shall furnish the certificate and endorsements for it within fourteen days after the change order is executed.
+
+## Where a technical standard requires a certificate of insurance specific to an operation, such as the demolition certificates under [[sync/building-demolition]], that certificate shall show the coverages and limits this standard requires and any additional coverage the technical standard names for that operation.
+
+## The limits a technical standard names for a service provider's own insurance, and the certificate a procurement step requires before award under [[sync/bidding-procedures]], are not changed by this standard; this standard governs the coverages the Contractor carries on the Work and how they are proved and kept in force, and the technical standards go on naming the operation-specific evidence they have always required. {note}