SynC · Topic
These are the standards in the SynC Standards library that cover Hardware. Each one is a complete, plain-language specification: the scope it applies to, the requirements that govern it, and a structured equipment datasheet listing the values a project has to decide — ratings, materials, setpoints, and the standards each is verified against. All of it is free to read without an account and published under CC BY-SA 4.0.
A standard usually carries several topics, so most of the entries below also appear under neighbouring subjects. The topics each one carries are listed on its own page.
Non-load-bearing extruded aluminum framing systems glazed with monolithic or insulating glass, and the aluminum stile-and-rail swing entrance doors integrated with them, at building perimeters and interior partitions. Covers framing depth, sightline, joinery, glazing pocket position, and thermal barrier construction; glass lite construction, insulating glass unit make-up, edge seal, and low-emissivity coatings; dry, wet, and structural silicone glazing methods; air infiltration, water penetration, structural wind load, thermal transmittance, solar heat gain, condensation, acoustic, windborne debris, and inter-story drift performance; entrance door leaf proportions, construction, hardware, thresholds, and weatherseals; anodic and organic finishes; perimeter anchorage, sill water management, and air and water control layer continuity; laboratory and field testing; installation, cleaning, protection, and warranty.
Swinging door openings furnished as one combined package of hollow metal doors and frames, architectural wood flush doors, and finish hardware, in commercial, institutional, and light-industrial construction. Covers the opening schedule as the coordination instrument; hollow metal performance levels, models, face-sheet materials, cores, frame thickness, profile, construction method, anchorage, grout fill, and factory finish; wood door duty levels, appearance grades, cores, face materials, veneer selection and matching, edges, and finishing; fire-rated and smoke-rated listed assemblies under NFPA 80, NFPA 105, and UL 10C; hinges, locksets, exit devices, closers, stops, protection plates, thresholds, and gasketing; cylinders, keyways, and keying hierarchy; electrified hardware, fail modes, power transfer, and fire alarm release; accessible-opening obligations; installation tolerances and clearances; fire door inspection at turnover; and warranty.
Factory-fabricated sheet-steel lockers and their doors, latching, locking, trim, interior equipment, and anchorage, in knocked-down or welded construction, for school corridors, athletic and team rooms, employee and industrial change rooms, public recreation, and day-use storage. Covers substrate selection and corrosion protection, component sheet thickness, tier and opening configuration, door ventilation, latching and locking including electronic locks, powder-coat finish performance, tops, bases and closure trim, accessible lockers under the ADA Standards and ICC A117.1, and floor, wall, and seismic anchorage.
Interior window treatments installed for glare control, solar heat control, daylight management, privacy, and room darkening in commercial, institutional, and light-industrial buildings. Covers manual and motorized roller shades with solar screen, room-darkening, and blackout fabrics, dual-roller assemblies carrying two shades on one mounting, and draperies on track systems. Addresses fabric composition, openness factor and solar optical properties, fire performance under NFPA 701 and ASTM E84, low-emitting certification, lightfastness, fungal and antimicrobial performance, roller tube and bracket hardware, fascia and pocket concealment, hembars, manual clutch operation and the cord retention provisions of ANSI/WCMA A100.1, motorized operation and its power, listing, control, and integration, mounting condition and light gap, perimeter light-control channels, accessible operation, field testing, installation, warranty, and spare parts.
Factory-fabricated architectural casework graded under the Architectural Woodwork Standards for commercial, institutional, educational, and healthcare buildings: plastic-laminate, thermally fused laminate, wood-veneer, and solid-wood base, wall, and tall cabinets; reception desks, nurse stations, service and transaction counters, and built-in millwork cabinetry; the plastic-laminate countertops and backsplashes that top them; and the cabinet hardware that operates them. Covers the quality grade, installation grade, and structural duty level; construction type and door and drawer-front interface style; core materials by moisture exposure; exposed and semi-exposed surface materials and laminate grades; veneer species, cut, and matching; edge treatment; plastic-laminate countertop construction; hinges, drawer slides, pulls, locks, and shelf supports; factory finishing; interior finish fire classification; composite-wood formaldehyde and adhesive emissions; accessible stations; blocking, anchorage, and seismic restraint; installation; warranty; and spare parts.