SynC · Topic
These are the standards in the SynC Standards library that cover Doors. Each one is a complete, plain-language specification: the scope it applies to, the requirements that govern it, and a structured equipment datasheet listing the values a project has to decide — ratings, materials, setpoints, and the standards each is verified against. All of it is free to read without an account and published under CC BY-SA 4.0.
A standard usually carries several topics, so most of the entries below also appear under neighbouring subjects. The topics each one carries are listed on its own page.
Non-load-bearing extruded aluminum framing systems glazed with monolithic or insulating glass, and the aluminum stile-and-rail swing entrance doors integrated with them, at building perimeters and interior partitions. Covers framing depth, sightline, joinery, glazing pocket position, and thermal barrier construction; glass lite construction, insulating glass unit make-up, edge seal, and low-emissivity coatings; dry, wet, and structural silicone glazing methods; air infiltration, water penetration, structural wind load, thermal transmittance, solar heat gain, condensation, acoustic, windborne debris, and inter-story drift performance; entrance door leaf proportions, construction, hardware, thresholds, and weatherseals; anodic and organic finishes; perimeter anchorage, sill water management, and air and water control layer continuity; laboratory and field testing; installation, cleaning, protection, and warranty.
Swinging door openings furnished as one combined package of hollow metal doors and frames, architectural wood flush doors, and finish hardware, in commercial, institutional, and light-industrial construction. Covers the opening schedule as the coordination instrument; hollow metal performance levels, models, face-sheet materials, cores, frame thickness, profile, construction method, anchorage, grout fill, and factory finish; wood door duty levels, appearance grades, cores, face materials, veneer selection and matching, edges, and finishing; fire-rated and smoke-rated listed assemblies under NFPA 80, NFPA 105, and UL 10C; hinges, locksets, exit devices, closers, stops, protection plates, thresholds, and gasketing; cylinders, keyways, and keying hierarchy; electrified hardware, fail modes, power transfer, and fire alarm release; accessible-opening obligations; installation tolerances and clearances; fire door inspection at turnover; and warranty.
Architectural vision glass and glazing for storefronts, curtain walls, windows, exterior and interior doors, sidelights, transoms, borrowed lites, partitions, and other building glazing infill. Covers annealed, heat-strengthened, and fully tempered flat glass; laminated glass; coated (low-emissivity and solar-control) glass; insulating glass units (IGUs) including double and triple makeups; spandrel and ceramic-frit glass; safety glazing in hazardous locations per the International Building Code; glass strength and thickness determination under wind and snow load per ASTM E1300; thermal stress and edge-condition selection of annealed versus heat-strengthened versus fully tempered glass; nickel-sulfide heat-soak treatment for tempered glass; low-iron glass; warm-edge spacers and inert-gas fill; structural silicone and dry-gasket glazing methods; setting blocks, edge clearances, and glazing accessories; and field installation, testing, cleaning, and warranty of the glass and glazing materials.
Field-applied surface preparation, primers, and finish coatings on interior architectural substrates — gypsum board, plaster and veneer plaster, concrete, concrete masonry, ferrous and galvanized metal, and interior wood — in commercial, institutional, and multi-family residential buildings. Covers latex, alkyd, and water-based epoxy paint systems applied to walls, ceilings, doors and frames, exposed structure, and exposed mechanical and electrical work that is to be field-painted.
Upward-acting sectional overhead doors whose horizontal panels (sections) hinge together and track horizontally beneath the ceiling when open, serving loading docks, drive-through service openings, parking garages, warehouses, and light-industrial buildings. Covers insulated (foamed polyurethane sandwich), non-insulated (ribbed or pan steel), and full-vision aluminum-and-glazing doors; panel material, gauge, thickness, and finish; vision lites and glazing; weatherseals and air-infiltration class; torsion and extension counterbalance and cycle-life rating; track and lift configuration selected by available headroom and sideroom; wind-load design pressure and reinforcement; manual chain-hoist and motor operation with UL 325 entrapment protection; installation, field testing including the safety-reverse test, and warranty.